Jump to the main content
GigaGone
Search

Search GigaGone

Why Does My Drive Show Less Space Than the Label?

By Published Topic: Storage Units & Capacity

Your drive shows less space mainly because makers count capacity in decimal (1 GB is 1,000,000,000 bytes) while Windows counts in binary (1 GiB is 1,073,741,824 bytes), so a 1 TB drive appears as about 931. Formatting and system files take a further share. Neither means the drive is faulty, unless the gap is far larger than these causes explain.

External drive with a tape measure and a blank slip of paper on a desk, with a NAS and laptop on a shelf behind

Part of the guide: Storage Units Explained: Bytes, GB, GiB and Why Drives Show Less

A new drive that shows less than its box says is almost always normal. It is covered in our storage units explained hub, and the short answer is a difference in counting plus some formatting overhead. The storage and backup glossary defines the terms used below.

The main reason: decimal vs binary

Seagate explains that makers market capacity in decimal, where 1 GB is 1,000,000,000 bytes. Windows counts in binary, where one unit is 1,073,741,824 bytes (NIST’s 1 GiB). The same bytes divide into a smaller number. The drive is not missing space; see Decimal vs binary units: why sizes differ.

What you will see

Approximate values from Seagate’s table:

Label macOS (newer) Windows
500 GB 500 GB 465 GB
1 TB 1 TB 931 GB
2 TB 2 TB 1.81 TB
4 TB 4 TB 3.63 TB
8 TB 8 TB 7.27 TB

Check any other size in the GB vs GiB converter. Checked on 2026-11-14.

Second reason: formatting and system files

Apple states that actual formatted capacity is less than the stated figure. Formatting and the operating system use some space, and on a phone the system and built-in apps do too. We give no fixed percentage, because it varies by file system and device.

Third reason: the volume does not use the whole drive

If the gap is far bigger than units explain, a partition may cover only part of the drive. Back up first, because partition tools can delete data. Then look at Disk Management on Windows or Disk Utility on a Mac, and use the maker’s or the operating system’s documentation.

When it is a problem

  • the shortfall is much larger than the table shows
  • the drive appears and disappears, or makes unusual noises
  • files are missing

Copy what you can to another place and stop using the drive. Contact the maker’s support or a qualified professional; see data loss and recovery. GigaGone offers no recovery service.

Planning with it in mind

When you choose a drive, subtract the units gap before sizing. The backup storage estimator and how to choose an external drive both help.

FAQ

Why does my 1 TB drive show 931 GB?

Because the drive holds 1,000,000,000,000 bytes and Windows divides by 1,073,741,824, the size of a binary gigabyte, giving about 931. Seagate documents this exact case. The space has not gone anywhere; the same byte count is just written in a larger unit. Our GB vs GiB page shows the working.

Is my drive faulty if it shows less space?

Usually not. A gap of roughly 7 percent at gigabyte size and about 9 percent at terabyte size is expected from units alone. If the gap is much larger, check the partition and the formatted size. Before changing anything on the drive, back up first. If you suspect failure, contact the maker’s support.

Do Macs show the full label capacity?

Seagate says newer macOS versions display decimal values that match the label, so a 1 TB drive shows as 1 TB, although Apple notes actual formatted capacity is less. Older macOS versions counted in binary. Check your version and compare with the maker’s own table for your capacity.

Does formatting reduce the space?

Yes, a little. Apple states that formatted capacity is less than the stated figure because formatting and the operating system use some space. The amount depends on the file system and settings, so we do not give a single figure. Back up first before reformatting, since formatting erases everything on the drive.

Why does my phone show less than 128 GB or 256 GB?

The same unit rule applies, and phones also reserve space for the operating system and built-in apps before you add anything. Apple says formatted capacity is less than the label for this reason. Check your phone maker’s support page for how it reports storage, and free up space only after backing up.

Can I get the missing space back?

The unit difference cannot be reversed, because it is only a counting convention. If a partition or volume does not use the whole drive, a disk tool can sometimes extend it, but changing partitions can delete data, so back up first and use the operating system’s documentation or the maker’s support.

Sources

  1. Seagate Support: Why does my hard drive report less capacity than the label?
  2. Seagate Support: Storage capacity measurement standards
  3. Apple Support: How storage capacity is reported
  4. NIST: Prefixes for binary multiples

Questions readers ask

Why does my 1 TB drive show 931 GB?

Because the drive holds 1,000,000,000,000 bytes and Windows divides by 1,073,741,824, the size of a binary gigabyte, giving about 931. Seagate documents this exact case. The space has not gone anywhere; the same byte count is just written in a larger unit. Our GB vs GiB page shows the working.

Is my drive faulty if it shows less space?

Usually not. A gap of roughly 7 percent at gigabyte size and about 9 percent at terabyte size is expected from units alone. If the gap is much larger, check the partition and the formatted size. Before changing anything on the drive, back up first. If you suspect failure, contact the maker's support.

Do Macs show the full label capacity?

Seagate says newer macOS versions display decimal values that match the label, so a 1 TB drive shows as 1 TB, although Apple notes actual formatted capacity is less. Older macOS versions counted in binary. Check your version and compare with the maker's own table for your capacity.

Does formatting reduce the space?

Yes, a little. Apple states that formatted capacity is less than the stated figure because formatting and the operating system use some space. The amount depends on the file system and settings, so we do not give a single figure. Back up first before reformatting, since formatting erases everything on the drive.

Why does my phone show less than 128 GB or 256 GB?

The same unit rule applies, and phones also reserve space for the operating system and built-in apps before you add anything. Apple says formatted capacity is less than the label for this reason. Check your phone maker's support page for how it reports storage, and free up space only after backing up.

Can I get the missing space back?

The unit difference cannot be reversed, because it is only a counting convention. If a partition or volume does not use the whole drive, a disk tool can sometimes extend it, but changing partitions can delete data, so back up first and use the operating system's documentation or the maker's support.

Further reading

  1. Seagate Support: Why does my hard drive report less capacity than the label? (seagate.com)
  2. Seagate Support: Storage capacity measurement standards (seagate.com)
  3. Apple Support: How storage capacity is reported (support.apple.com)
  4. NIST: Prefixes for binary multiples (physics.nist.gov)

Worth reading next

Back to top